Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Electrolux EFMEUTT owners to properly answer your question. This manual comes under the category Dryers and has been rated by 1 people with an average of a 9.
This manual is available in the following languages: English. Is your question not listed? Ask a question. Dito ELX Dito ELX65F Dito ELX65F5. EDC Instruction Book. EDC W. EDC M. EDC E. Installation And Instruction Manual.
Instruction Booklet. Operating Instructions Manual. User Information. EDE W. EDE M. EDE E. EDE French Notice D'utilisation. EDH W. Installation Instruction. EDI W. EDR Electric Dryer. Instructions Manual. Gas Dryer. Capacity Gas Dryer. Owner's Manual. Installation Manual. Factory Parts Catalog. Locate the dryer within reach of the receptacle for the length power cord to be purchased, allowing some slack in the cord. Refer to the pre-installation requirements in this manual for the proper power cord to be purchased.
If the strain relief is not attached, the cord can be pulled out of the dryer and can be cut by any movement of the cord, resulting in electrical shock. A chemical reaction occurs between copper and aluminum and can cause electrical shorts. The proper wiring and receptacle is a copper wired power cord with a copper wired receptacle.
Dryers operating on volt power supply will have longer drying times than dryers operating on volt power supply. Improper connection of the equipment grounding conductor can result in a risk of electrical shock.
Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded. The dryer MUST be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical current. After you purchase and install a 3 wire or 4 wire power supply cord having an equipmentgrounding conductor and a grounding plug that matches your wiring system, the plug MUST be plugged into an appropriate, copper wired receptacle that is properly installed and.
If in doubt, call a licensed electrician. The dryer MUST be connected to a grounded metal, permanent wiring system; or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.
Since your dryer is equipped with a power supply cord having an equipment-grounding conductor and a grounding plug, the plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. DO NOT modify the plug provided with this appliance. The dryer is equipped with a three-prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle.
The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Failure to disconnect power source before servicing could result in personal injury or even death. Turn off power supply to outlet. Remove the screw securing the terminal block access cover in the lower corner on the back of the dryer.
At this time, the strain relief should be loosely in place. Tighten the screw securely. Attach the remaining two power cord outer conductors to the outer, BRASS colored terminals on the terminal block.
Tighten both screws securely. Reinstall the terminal block cover. If moving dryer from a 4-wire system and installing it in a 3-wire system, move the internal ground from the center terminal back to the GREEN screw next to the terminal block. UL-appr ove d s train relief here. Ter minal screw reco v ery slot. If a terminal screw falls during cord installation, it can be retrieved in the terminal screw recovery slot below the access panel. DO NOT remove in ter nal gro u nd i n.
Remove the shipping cap from gas pipe at the rear of the dryer. Wait a few minutes for gas to move through the gas line. Check for gas system leaks with a manometer.
If a manometer is not available, test all connections by brushing on a soapy water. The supply line must be equipped with an approved manual shutoff valve. This valve should be located in the same room as the dryer and should be in a location that allows ease of opening and closing. Do not block access to the gas shutoff valve. Water pressure MUST be between 30 and psi. Your water. Turn off COLD water supply to washer,. Replace washer if it is torn or worn out. Momentarily turn on COLD supply and run some water into a bucket or container to clear any contaminants in the line.
Remove hose kit from dryer drum and inspect hose couplings for proper placement of rubber washers. Turn on the water and check for leaks at all connections. Connect the exhaust duct to the outside exhaust system see pages 5 through 7. Use metal foil tape to seal all other joints.
Adjust one or more of the legs until the dryer is resting solidly on all four legs. Place a level on. Rock alternating. It contains valuable and helpful. See the next page about performing a brief,. If you have any questions during initial. Place these instructions in a location near the dryer for future reference. Also see that nothing such as boxes, clothing, etc. On gas dryers, before the burner will light, it is necessary for the gas line to be bled of air. If this happens, press cancel and wait 5 minutes before making another attempt to light.
Wake up the dryer again by pressing any button, then immediately and simultaneously press and hold buttons 2a and 2b for 5 seconds, or until the LCD display changes. Press the start button. The Installation Cycle will automatically per-. Your dryer will exit the Installation Cycle and return to normal operation the next time you wake it up. The Installation Cycle will automatically test for correct cord connection on electric models , presence of.
Dryer will stay awake for 3 minutes after the Installation Cycle. If you wish to immediately run the dryer through a drying cycle, press the cancel button to put the unit to sleep and then rewake it immediately to continue the normal operating mode.
C Removing Hinge from Front Panel. Attach with 2 short, course-thread, panhead screws. I Reinserting Latch Indicator.
0コメント